You can check which nodes are connected in the network, who is +logged on locally, who is logged on at all the nodes or even +just one node in particular. This is handy if you wish to see whether +a friend is connected at the node they use. To see who is connected +to the nodes, the SHOW/CONFIGURATION command is used. +
Example: +
+
+
+show/configuration
+show/configuration/nodes
+show/configuration (node_call)
+show/configuration (prefix)
+
+The first of our three examples would output something like this, +
+
+sh/c +Node Callsigns +EI5TCR (7 users) +GB7ADX +GB7BAA G4FPV G8TIC +GB7BIG (GD0TEP) GD3UMW +GB7BPQ (G0INA) G0RCI G3AKU G3OCA +(GB7CDX) G3JNB G4ALR +GB7DJK G0FYD G0REK G1TLH G4PEL G4SOZ + G4TVR G7SQW K8AZ M0CTQ-1 MM1CXE-10 + ON7WP +GB7DXA G0RDI G8SJP +GB7DXC (G0HDB) G0WFK (G1FYC) G3KWK G3LME + G3OIL G4BGW G4FUJ (G4PDQ) GW7SMV +GB7DXE G1NNB +(GB7DXG) GU6EFB GU7DHI +GB7DXK G1NTW G3IBI G3NSM G3XAQ G4CUS + G4XQY G7GAN +GB7DXM G1EUC G3GAF G3LAS G4ZTR G8WXU + M0BCT M1EMF ++
You will notice that EI5TCR is showing only that it has 7 users and not +giving the actual callsigns. This means that this node is on a limited +protocol of some kind, probably because of a contest situation where +slow radio links can block up and fail if too much information is sent +between nodes. +
The second example would just show the nodes connected in the +network, like this, +
+
+sh/c/n +Node Callsigns +GB7BAA GB7BAA GB7BPQ (GB7CDX) GB7DJK GB7DXA + GB7DXC GB7DXE (GB7DXG) GB7DXK GB7DXL + GB7DXM GB7DXS GB7IPT GB7MRS GB7UJS + GB7YDX KL7G N2TLY (ON0DXK) +GB7BIG EI5TCR GB7ADX GB7BIG GB7UDX +GB7MBC +PA4AB-14 PA4AB-14 +PI4TUE-8 PI4TUE-8 ++
If we insert the node_call pi4tue-8 into the third example, then +this would be the output, +
+
+Node Callsigns +PI4TUE-8 9A1CMA-6 DF6PW DL4FAY DL4KAK DL4WF-2 + F5NOD-2 F5PAC IZ0CSR N6CR OH2BLD + ON1LVL-13 ON4CBT ON4CJP ON5DXL-14 ON7NQ + PA0RCT PA3DYS PA3FDO PA5KW-4 PI4TUE-9 + YT1XX ++
As you can see, only the users of the requested node are shown. +
You can also use a prefix to show only a group of nodes. For example +you may only wish to see who is connected to the nodes in the UK. To +do this simply use a prefix like this ... +
+
+show/configuration gb7 ++
To show the locally connected users, the SHOW/USERS command is +used +
Example: +
+
+
+show/users
+
+The output of this command would look like this, +
+
+Callsigns connected to GB7MBC +G0JHC G0NEI G0VGS G0VGS-2 G0YLM +G3JAG G3OWO G3UEU ++
+