+
+=== 0^SET/ADDRESS <your address>^Record your postal address
+
+=== 0^SET/ANNOUNCE^Allow announce messages to come out on your terminal
+=== 0^UNSET/ANNOUNCE^Stop announce messages coming out on your terminal
+
+=== 5^SET/ARCLUSTER <call> [<call>..]^Make the callsign an AR-Cluster node
+
+=== 0^SET/BEEP^Add a beep to DX and other messages on your terminal
+=== 0^UNSET/BEEP^Stop beeps for DX and other messages on your terminal
+
+=== 5^SET/CLX <call> [<call>..]^Make the callsign an CLX node
+
+=== 9^SET/DEBUG <name>^Add a debug level to the debug set
+=== 9^UNSET/DEBUG <name>^Remove a debug level from the debug set
+
+=== 0^SET/DX^Allow DX messages to come out on your terminal
+=== 0^UNSET/DX^Stop DX messages coming out on your terminal
+
+=== 0^SET/DXGRID^Allow Grid Squares on the end of DX announcements
+=== 0^UNSET/DXGRID^Stop Grid Squares on the end of DX announcements
+A standard feature which is enabled in version 1.43 and above is
+that if the spotter's grid square is known it is output on the end
+of a DX announcement (there is just enough room). Some user programs
+cannot cope with this. You can use this command to reset (or set)
+this feature.
+
+=== 5^SET/DXNET <call> [<call>..]^Make the callsign an DXNet node
+
+=== 0^SET/ECHO^Make the cluster echo your input
+=== 0^UNSET/ECHO^Stop the cluster echoing your input
+If you are connected via a telnet session, different implimentations
+of telnet handle echo differently depending on whether you are
+connected via port 23 or some other port. You can use this command
+to change the setting appropriately.
+
+The setting is stored in your user profile.
+
+YOU DO NOT NEED TO USE THIS COMMAND IF YOU ARE CONNECTED VIA AX25.
+
+=== 0^SET/HERE^Tell the system you are present at your terminal
+=== 0^UNSET/HERE^Tell the system you are absent from your terminal
+
+=== 0^SET/HOMENODE <node> ^Set your normal cluster callsign
+Tell the cluster system where you normally connect to. Any Messages sent
+to you will normally find their way there should you not be connected.
+eg:-
+ SET/HOMENODE gb7djk
+
+=== 9^SET/ISOLATE^Isolate a node from the rest of the network
+Connect a node to your system in such a way that you are a full protocol
+member of its network and can see all spots on it, but nothing either leaks
+out from it nor goes back into from the rest of the nodes connected to you.
+
+You can potentially connect several nodes in this way.
+
+=== 9^UNSET/ISOLATE^Stop Isolation of a node from the rest of the network
+Remove isolation from a node - SET/ISOLATE
+
+=== 0^SET/LANGUAGE <lang>^Set the language you want to use
+You can select the language that you want the cluster to use. Currently
+the languages available are en (english) and nl (dutch).
+
+=== 0^SET/LOCATION <lat & long>^Set your latitude and longitude
+=== 9^SET/SYS_LOCATION <lat & long>^Set your cluster latitude and longitude
+In order to get accurate headings and such like you must tell the system
+what your latitude and longitude is. If you have not yet done a SET/QRA
+then this command will set your QRA locator for you. For example:-
+ SET/LOCATION 52 22 N 0 57 E
+
+=== 0^SET/LOGININFO^Inform when a station logs in locally
+=== 0^UNSET/LOGININFO^Inform when a station logs out locally
+
+=== 9^SET/LOCKOUT <call>^Stop a callsign connecting to the cluster
+=== 9^UNSET/LOCKOUT <call>^Allow a callsign to connect to the cluster
+
+=== 0^SET/NAME <your name>^Set your name
+Tell the system what your name is eg:-
+ SET/NAME Dirk
+
+=== 5^SET/NODE <call> [<call>..]^Make the callsign an AK1A cluster
+Tell the system that the call(s) are to be treated as AK1A cluster and
+fed PC Protocol rather normal user commands.
+
+=== 8^SET/OBSCOUNT <count> <nodecall>^Set the 'pump-up' obscelence counter
+From 1.35 onwards neighbouring nodes are pinged at regular intervals (see
+SET/PINGINTERVAL), usually 300 seconds or 5 minutes. There is a 'pump-up'
+counter which is decremented on every outgoing ping and then reset to
+the 'obscount' value on every incoming ping. The default value of this
+parameter is 2.
+
+What this means is that a neighbouring node will be pinged twice at
+(default) 300 second intervals and if no reply has been heard just before
+what would be the third attempt, that node is disconnected.
+
+If a ping is heard then the obscount is reset to the full value. Using
+default values, if a node has not responded to a ping within 15 minutes,
+it is disconnected.
+
+=== 0^SET/PAGE <lines per page>^Set the lines per page
+Tell the system how many lines you wish on a page when the number of line
+of output from a command is more than this. The default is 20. Setting it
+explicitly to 0 will disable paging.
+ SET/PAGE 30
+ SET/PAGE 0
+
+The setting is stored in your user profile.
+
+=== 9^SET/PINGINTERVAL <time> <nodecall>^Set ping time to neighbouring nodes
+As from release 1.35 all neighbouring nodes are pinged at regular intervals
+in order to determine the rolling quality of the link and, in future, to
+affect routing decisions. The default interval is 300 secs or 5 minutes.
+
+You can use this command to set a different interval. Please don't.
+
+But if you do the value you enter is treated as minutes up 60 and seconds
+for numbers greater than that.
+
+This is used also to help determine when a link is down at the far end
+(as certain cluster software doesn't always notice), see SET/OBSCOUNT
+for more information.
+
+=== 9^SET/PRIVILEGE <n> <call> [<call..]^Set privilege level on a call
+Set the privilege level on a callsign. The privilege levels that pertain
+to commands are as default:-
+ 0 - normal user
+ 1 - allow remote nodes normal user RCMDs
+ 5 - various privileged commands (including shutdown, but not disc-
+ connect), the normal level for another node.
+ 8 - more privileged commands (including disconnect)
+ 9 - local sysop privilege. DO NOT SET ANY REMOTE USER OR NODE TO THIS
+ LEVEL.
+If you are a sysop and you come in as a normal user on a remote connection
+your privilege will automatically be set to 0.
+
+=== 9^SET/PASSWORD <callsign> <string>^Set a users password
+The password for a user can only be set by a full sysop. The string
+can contain any characters but any spaces are removed (you can type in
+spaces - but they won't appear in the password). You can see the
+result with STAT/USER.
+
+=== 5^SET/SPIDER <call> [<call>..]^Make the callsign an DXSpider node
+Tell the system that the call(s) are to be treated as DXSpider node and
+fed new style DX Protocol rather normal user commands.
+
+=== 9^SET/SYS_QRA <locator>^Set your cluster QRA locator
+=== 0^SET/QRA <locator>^Set your QRA locator
+Tell the system what your QRA (or Maidenhead) locator is. If you have not
+done a SET/LOCATION then your latitude and longitude will be set roughly
+correctly (assuming your locator is correct ;-). For example:-
+ SET/QRA JO02LQ
+
+=== 0^SET/QTH <your qth>^Set your QTH
+Tell the system where you are. For example:-
+ SET/QTH East Dereham, Norfolk
+
+=== 0^SET/TALK^Allow TALK messages to come out on your terminal
+=== 0^UNSET/TALK^Stop TALK messages coming out on your terminal
+
+=== 0^SET/WCY^Allow WCY messages to come out on your terminal
+=== 0^UNSET/WCY^Stop WCY messages coming out on your terminal
+
+=== 0^SET/WWV^Allow WWV messages to come out on your terminal
+=== 0^UNSET/WWV^Stop WWV messages coming out on your terminal
+
+=== 0^SET/WX^Allow WX messages to come out on your terminal
+=== 0^UNSET/WX^Stop WX messages coming out on your terminal
+
+=== 0^SHOW/CALL <callsign>^Show any callbook details on a callsign
+This command queries an international callbook server on the internet
+and returns any information available for that callsign.
+
+=== 0^SHOW/DATE [<prefix>|<callsign>]^Show the local time
+This is very nearly the same as SHOW/TIME, the only difference the format
+of the date string if no arguments are given.
+
+If no prefixes or callsigns are given then this command returns the local
+time and UTC as the computer has it right now. If you give some prefixes
+then it will show UTC and UTC + the local offset (not including DST) at
+the prefixes or callsigns that you specify.
+
+=== 0^SHOW/DX^Interrogate the spot database
+If you just type SHOW/DX you will get the last so many spots
+(sysop configurable, but usually 10).
+
+In addition you can add any number of these commands in very nearly
+any order to the basic SHOW/DX command, they are:-
+
+on <band> - eg 160m 20m 2m 23cm 6mm
+on <region> - eg hf vhf uhf shf (see SHOW/BANDS)
+
+<number> - the number of spots you want
+<from>-<to> - <from> spot no <to> spot no in the selected list
+
+<prefix> - for a spotted callsign beginning with <prefix>
+*<suffix> - for a spotted callsign ending in <suffix>
+*<string>* - for a spotted callsign containing <string>
+
+day <number> - starting <number> days ago
+day <from>-<to> - <from> days <to> days ago
+
+info <text> - any spots containing <text> in the info or remarks
+
+by <call> - any spots spotted by <call> (spotter <call> is the
+ same).
+
+qsl - this automatically looks for any qsl info on the call
+ held in the spot database.
+
+iota [<iota>] - If the iota island number is missing it will look for
+ the string iota and anything which looks like an iota
+ island number. If you specify then it will look for
+ that island.
+
+qra [<locator>] - this will look for the specific locator if you specify
+ one or else anything that looks like a locator.
+
+e.g.
+
+ SH/DX 9m0
+ SH/DX on 20m info iota
+ SH/DX 9a on vhf day 30
+ SH/DX rf1p qsl
+ SH/DX iota
+ SH/DX iota eu-064
+ SH/DX qra jn86